Note
For the most accurate list of Publications, please visit:
http://homepages.cae.wisc.edu/~zhous/
Accepted papers
-
28. Jin, N., Zhou, S., Chang, and Huang, 2006,
“Influential Process Variable Selection for Surface Quality Control in Hot Rolling Processes”,
IEEE Transactions on Automation Science and Engineering, conditionnaly accepted.
2007
-
27. Li Z., Zhou S., Choubey S., and Sievenpiper C., 2006,
“Failure Event Prediction Using Cox Proportional Hazard Model Driven by Frequent Failure Signatures”,
IIE Transactions on Quality and Reliability Engineering, 39, 303–315.
-
26. Li, Z., Zhou, S., Ding, Y., 2007,
“Pattern Matching for Root Cause Identification of Manufacturing Processes with Consideration of General Structured Noise”,
IIE Transactions on Quality and Reliability Engineering, 39, 251–263 .
-
25. Loose, J-P., Zhou, S., Ceglarek, D., 2007,
“Kinematic Analysis of Dimensional Variation Propagation for Multistage Machining Processes with General Fixture Layouts”,
IEEE Transactions on Automation Science and Engineering, 4(2), 141-152.
2006
-
24. Ren Y., Ding, Y., and Zhou, S., 2006,
“A Data-mining Approach to Study the Significance of Nonlinearity in Multi-Station Assembly Processes”,
IIE Transactions on Quality and Reliability Engineering, 38, pp.1069-1083.
-
23. Jin, N. and Zhou, S., 2006,
“Data-Driven Variation Source Identification of Manufacturing Processes Based on Eigenspace Comparison”,
Naval Research Logistics, 53(5), pp383-396.
-
22. Jin, N. and Zhou, S., 2006,
“Signature Construction and Matching for Fault Diagnosis in Manufacturing Processes through Fault Space Analysis”,
IIE Transactions, 38,pp.341-354.
-
21. Zhou, S., Sun, B., Shi, J., 2006,
“An SPC Monitoring System for Cycle-Based Waveform Signals Using Haar Transform”,
IEEE Transactions on Automation Science and Engineering, 37,pp.971-982.
-
20. Li, Z., Zhou, S., 2006,
“Robust Method of Multiple Variation Sources Identification in Manufacturing Processes for Quality Improvement”,
ASME Transactions, Journal of Manufacturing Science and Engineering, 128(1), pp.326-336.
2005
-
19. Ding, Y., Zeng, L. and Zhou, S., 2005,
“Phase I Analysis for Monitoring Nonlinear Profile Signals in Manufacturing Processes”,
Journal of Quality Technology, 38(3), 199-216.
-
18. Jin, J., Guo, H., and Zhou, S., 2005,
“Supervisory Generalized Predictive Control Combining with Statistical Process Control for Thin Film Deposition Processes”,
ASME Transactions, Journal of Manufacturing Science and Engineering, 128(1), pp.315-325.
-
17. Zhou, S., Jin, N., Jin, J., 2005,
“A New Directional Variant Multivariate Control Chart System Considering Known Process Faulty Conditions”,
IIE Transactions, 37, pp.971-982.
-
16. Zhou, S. and Jin, J., 2005,
“An Unsupervised Clustering Method For Cycle-Based Waveform Signals In Manufacturing Processes”,
IIE Transactions on Quality and Reliability Engineering, 37, pp.569-584.
-
15. Ding, Y., Zhou, S., and Chen, Y., 2005,
“A Comparison of Process Variation Estimators for In-Process Dimensional Measurements and Control”,
ASME Transactions, Journal of Dynamic Systems, Measurement and Control, 127, pp69-79.
2004
-
14. Ceglarek, D., Huang, W., Zhou, S., Ding, Y., Kumar, R., and Zhou, Y., 2004,
“Time-Based Competition in Multistage Manufacturing, Stream-of-Variation Methodology (SOVA) – A Review”,
International Journal of Flexible Manufacturing Systems, 16, pp11-44.
-
13. Jin, N., Zhou, S., and Chang, T., 2004,
“Identification of impacting factors of surface defects in hot rolling processes using multi-level regression analysis”,
Transactions of NAMRI/SME, 32, pp.557-564.
-
12. Zhou, S., Chen, Y., and Shi, J., 2004,
“Root Cause Estimation and Statistical Testing for Quality Improvement of Multistage Manufacturing Processes”,
IEEE Transactions on Automation Science and Engineering, 1(1), pp73-83.
-
11. Zhou, S., Shin, K., Dyer, S., Shi, J., Ni, J., 2004,
“Extended Influence Coefficient Method for Rotor Active Balancing during Acceleration”,
ASME Transactions, Journal of Dynamic Systems, Measurement and Control, 126, pp219-223.
-
10. Zhou, S. and Shi, J., 2004,
“Identification of Nonlinear Effects in Rotor Systems Using Recursive QR Factorization Method”,
Journal of Sound and Vibration, 270, pp.455 –469.
2003
-
9. Zhou, S., Ding, Y., Chen, Y., Shi, J., 2003,
“Diagnosability study of multistage manufacturing processes based on linear mixed-effects models”,
Technometrics, 45(4), pp312~325.
-
8. Zhou, S., Huang, Q., Shi, J., 2003,
“State Space Modeling of Dimensional Variation Propagation in Multistage Machining Process Using Differential Motion Vectors”,
IEEE Transactions on Robotics and Automation, 19(2),pp296-309.
2002
-
7. Huang, Q., Zhou, S., Shi, J., 2002,
“Diagnosis of Multi-Operational Machining Processes by Using Virtual Machining”,
Robotics and Computer Integrated Manufacturing, 18, pp.233 –239.
-
6. Zhou, S. and Shi, J., 2002,
“Optimal One-Plane Active Balancing of Rigid Rotor during Acceleration”,
Journal of Sound and Vibration, 249(1), pp.196-205.
2001
-
5. Zhou, S. and Shi, J., 2001,
“Active Balancing and Vibration Control of Rotating Machinery: A Survey”,
The Shock and Vibration Digest, 33(5), pp361-371.
-
4. Zhou, S. and Shi, J., 2001,
“Imbalance Estimation for Speed-Varying Rigid Rotors Using Time-Varying Observer”,
ASME Transactions, Journal of Dynamic Systems, Measurement, and Control, 123, pp637-644.
-
3. Zhou, S. and Shi, J., 2001,
“The Analytical Unbalance Response of Jeffcott Rotor during Acceleration”,
", ASME Transactions, Journal of Manufacturing Science and Engineering, Vol. 123, No. 2, pp299-302.
2000
1998
